Strona 1 z 2 12 OstatniOstatni
Pokaż wyniki 1 do 10 z 11

Temat: Wszytsko sie zacina.... :/

  1. #1
    Zarejestrowany
    Dec 2006
    Postów
    693

    Domyślnie Wszytsko sie zacina.... :/

    Witam otuz mam problem zacina mi sie system. Mam mandrive 2007.
    Od wczoraj dokladnie mi sie kazde okno tnie jak przelaczam np. z konsoli na przglodarke albo kadu to to sie tak zacina ze musz eoklo 7 sek czkeac az sie przołczy...

  2. #2
    Zarejestrowany
    Nov 2006
    Skąd
    Polska/Poland
    Postów
    1,191

    Domyślnie

    coś zajmuje Ci procka i pewnie dlatego są zaciachy....
    zapodaj w shell'u polecenie
    Kod:
    top
    to zobaczysz co zamula.
    ***********
    * markossx *
    ***********

  3. #3
    Zarejestrowany
    Jun 2006
    Skąd
    rand(.eu)
    Postów
    8,748

    Domyślnie

    zobacz 'dmesg' czy nie bedziesz mial ladnych bledow z czyms co zawiera 'IDE reset' albo 'Seek error' - ewidentny pad dysku... czas na wymiane dopuki jeszcze sa na nim dane... moga to byc bledy pamieci operacyjnej - uszkodzony RAM albo cache procesora (raczej procek niz RAM bo przy awarii RAMcu bylyby niekontrolowane reboot'y)...

    Nie jest to zasada ale tak najczesciej bylo w przypadkach ktore widzialem przez ostatnie 8-10 lat...
    ctrl-alt-del.cc - soft reset site for IT admins and other staff :-)

  4. #4
    Zarejestrowany
    Dec 2006
    Postów
    693

    Domyślnie

    1. tgm po wpisaniu mam takie cos:

    Kod:
    http://img383.imageshack.us/my.php?image=zrzutekranu3jp3.png
    tylko juz dluzej nie czkalem az wczyta... bo puzniej zaczelo znikac i sie pojawaic z:
    891 na 795 potem do 131 i spowrotem....


    2. markossx jak wpislem:
    tylko koncowke ci pokaze bo cale sie nie zmeisci
    1.[code]

    Kod:
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
    ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
    ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
    PCI: VIA IRQ fixup for 0000:00:10.0, from 10 to 1
    uhci_hcd 0000:00:10.0: UHCI Host Controller
    uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:10.0: irq 17, io base 0x0000d800
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
    PCI: VIA IRQ fixup for 0000:00:10.1, from 10 to 1
    uhci_hcd 0000:00:10.1: UHCI Host Controller
    uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:10.1: irq 17, io base 0x0000dc00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
    PCI: VIA IRQ fixup for 0000:00:10.2, from 5 to 1
    uhci_hcd 0000:00:10.2: UHCI Host Controller
    uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:10.2: irq 17, io base 0x0000e000
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
    PCI: VIA IRQ fixup for 0000:00:10.3, from 5 to 1
    uhci_hcd 0000:00:10.3: UHCI Host Controller
    uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:10.3: irq 17, io base 0x0000e400
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    usb 1-1: new low speed USB device using uhci_hcd and address 2
    usb 1-1: configuration #1 chosen from 1 choice
    usb 1-2: new full speed USB device using uhci_hcd and address 3
    usb 1-2: configuration #1 chosen from 1 choice
    input: Chicony USB Wireless HID Receiver as /class/input/input2
    usbcore: registered new driver usbkbd
    drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
    usbcore: registered new driver hiddev
    ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
    ehci_hcd 0000:00:10.4: EHCI Host Controller
    ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
    ehci_hcd 0000:00:10.4: irq 17, io mem 0xfa010000
    ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 8 ports detected
    input: Chicony USB Wireless HID Receiver as /class/input/input3
    usb 1-1: USB disconnect, address 2
    usbcore: registered new driver usbmouse
    drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    usb 1-2: USB disconnect, address 3
    usb 1-1: new low speed USB device using uhci_hcd and address 4
    usb 1-1: configuration #1 chosen from 1 choice
    input: Chicony USB Wireless HID Receiver as /class/input/input4
    input: Chicony USB Wireless HID Receiver as /class/input/input5
    input,hiddev0: USB HID v1.10 Device [Chicony USB Wireless HID Receiver] on usb-0000:00:10.0-1
    input: Chicony USB Wireless HID Receiver as /class/input/input6
    usb 1-2: new full speed USB device using uhci_hcd and address 5
    usb 1-2: configuration #1 chosen from 1 choice
    ts: Compaq touchscreen protocol output
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected VIA KT880 chipset
    agpgart: AGP aperture is 128M @ 0xe8000000
    device-mapper: 4.6.0-ioctl (2006-02-17) initialised: [email protected]
    EXT3 FS on hda5, internal journal
    Adding 1100412k swap on /dev/hda7.  Priority:-1 extents:1 across:1100412k
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on hda8, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    Supermount version 2.0.4 for kernel 2.6
    NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE].
    NTFS volume version 3.1.
    loop: loaded (max 8 devices, max 1 partitions per device)
    hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    ACPI: Power Button (FF) [PWRF]
    ACPI: Power Button (CM) [PWRB]
    Using specific hotkey driver
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 2.4 (4095 buckets, 32760 max) - 224 bytes per conntrack
    Removing netfilter NETLINK layer.
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    end_request: I/O error, dev fd0, sector 0
    NET: Registered protocol family 17
    ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
    ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
    ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:11.5 to 64
    8139too Fast Ethernet driver 0.9.27
    ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 19
    eth0: RealTek RTL8139 at 0xe0f46000, 00:0f:ea:8c:a9:44, IRQ 19
    eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
    eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
    martian source 255.255.255.255 from 192.168.1.1, on dev eth0
    ll header: 00:0f:ea:8c:a9:44:00:19:4b:4b:5b:4a:08:00
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    IPv6 over IPv4 tunneling driver
    ip_tables: (C) 2000-2006 Netfilter Core Team
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 2.4 (4095 buckets, 32760 max) - 224 bytes per conntrack
    ClusterIP Version 0.8 loaded successfully
    ipt_recent v0.3.1: Stephen Frost <[email protected]>.  http://snowman.net/projects/ipt_recent/
    eth0: no IPv6 routers present
    netfilter PSD loaded - (c) astaro AG
    IFWLOG: register target
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 0 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 1 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 2 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 3 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 4 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 5 changed to on
    Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32771 DPT=7741 LEN=24
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32787 DPT=7741 LEN=24
    [[email protected] ~]$

  5. #5
    Zarejestrowany
    Jun 2006
    Skąd
    rand(.eu)
    Postów
    8,748

    Domyślnie

    a co daje 'dmesg | tail -n 50' ?!
    ctrl-alt-del.cc - soft reset site for IT admins and other staff :-)

  6. #6
    Zarejestrowany
    Dec 2006
    Postów
    693

    Domyślnie

    FDC 0 is a post-1991 82077
    end_request: I/O error, dev fd0, sector 0
    NET: Registered protocol family 17
    ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
    ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
    ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:11.5 to 64
    8139too Fast Ethernet driver 0.9.27
    ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 19
    eth0: RealTek RTL8139 at 0xe0f46000, 00:0f:ea:8c:a9:44, IRQ 19
    eth0: Identified 8139 chip type 'RTL-8100B/8139D'
    eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
    martian source 255.255.255.255 from 192.168.1.1, on dev eth0
    ll header: 00:0f:ea:8c:a9:44:00:19:4b:4b:5b:4a:08:00

  7. #7
    Zarejestrowany
    Dec 2006
    Postów
    693

    Domyślnie

    i 2 czesc

    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    IPv6 over IPv4 tunneling driver
    ip_tables: (C) 2000-2006 Netfilter Core Team
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 2.4 (4095 buckets, 32760 max) - 224 bytes per conntrack
    ClusterIP Version 0.8 loaded successfully
    ipt_recent v0.3.1: Stephen Frost <[email protected]>. http://snowman.net/projects/ipt_recent/
    eth0: no IPv6 routers present
    netfilter PSD loaded - (c) astaro AG
    IFWLOG: register target
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 0 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 1 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 2 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).

  8. #8
    Zarejestrowany
    Dec 2006
    Postów
    693

    Domyślnie

    i 3 czesc

    bootsplash: status on console 3 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 4 changed to on
    bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3).
    bootsplash: status on console 5 changed to on
    Shorewall:net2allROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32771 DPT=7741 LEN=24
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    Shorewall:net2allROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32787 DPT=7741 LEN=24
    Shorewall:net2allROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32788 DPT=7741

  9. #9
    Zarejestrowany
    Jun 2006
    Skąd
    rand(.eu)
    Postów
    8,748

    Domyślnie

    No to juz sam nie wiem... jakby cos nie tak z systemem/sprzetem to powinno miec jakies odbicie w dmesg'u... sorki ale nie mam czasu teraz sie dalej wglebiac...
    ctrl-alt-del.cc - soft reset site for IT admins and other staff :-)

  10. #10
    Zarejestrowany
    Dec 2006
    Postów
    693

    Domyślnie

    i 4

    LEN=24
    Shorewall:net2allROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32813 DPT=7741 LEN=24
    atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
    atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
    atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
    atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
    Shorewall:net2allROP:IN=eth0 OUT= MAC= SRC=192.168.1.11 DST=192.168.1.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32868 DPT=7741 LEN=24
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    [[email protected] ~]$

    sory ze tyle psotow ale w 1 sie nei miesci

Strona 1 z 2 12 OstatniOstatni

Zasady Postowania

  • Nie możesz zakładać nowych tematów
  • Nie możesz pisać wiadomości
  • Nie możesz dodawać załączników
  • Nie możesz edytować swoich postów
  •  
Subskrybuj

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52